#Pre painnt wipe rages free

Then, properly disposed of materials at your local hazmat - Maintaining a black car’s exterior is an intimidating experience considering a single finger swiped across the paint can show a noticeable blemish. To avoid spontaneous combustion, submerse all materials soaked in Penofin into a bucket of water and seal. Once wood fibers become fully protected, maintenance will become less frequent.Ĭaution: Do not apply to wood that is hot to the touch. This should be done several times the first year for maximum surface penetration. Re-apply Penofin as soon as wood appears dry or faded.

Surface will be dry to touch in 3 hours, but be sure to allow 24 hours before using.

Remove excess product by wiping the entire surface with a nap-free cloth.

Wait 20 to 30 minutes for the stain to absorb.

Do not over apply or surface will become tacky or sticky.

Apply a light coat to clean, dry, unfinished wood by using a stain pad, pump sprayer or high quality China bristle brush.

For some hardwood applications, pre-sand the surface with 60-to-80 grit sandpaper.

One gallon of Penofin Exotic Hardwood Stain provides 300-400 square feet of coverage.

Measure and purchase the correct amount of product needed.

Penofin Green Label – For restoration of the natural beauty and texture of pressure-treated wood.

Penofin Bronze Label – For protection of exotic hardwoods like: mahogany, teak, ipe, brazilian redwood and more.

Penofin Redwood All Heart – For bringing out the rich, dark, mahogany-red color with ever changing velvety sheen to any type of redwood.

Penofin Red Label – For protection of decks, siding, fences, log homes, and furniture from rain, wind, snow and other elements in high elevations.

Penofin Blue Label – For protection of decks, siding, fences, log homes, and furniture from discoloration.

Penofin Marine Stain – including oil, matte, and satin finish for docks and other water environments.

Interior Wood Stain – including environmentally friendly and natural tone finishes.

Exterior Wood Stain – including oil, matte and satin finish for siding, decks, furniture and more.

Wood Preperation Products – including wood stripper, cleaner, and brightener.

Penofin Products at DIY Home Center include: It will easily blend in with the rest of the application. You will also never need to strip or sand again! Simply clean the wood thoroughly, let dry and apply a light coat to any areas of the wood that may show wear and tear. You will never see a surface film when using Penofin, so you will never see cracking, bubbling, or peeling. A Penofin application is easy to maintain when applied according to directions. Rosewood Oil allows the wood to retain its flexibility and creates no surface film. All Penofin stains contain Brazilian Rosewood Oil which is a strong, flexible, water-resistant, mildew-resistant oil that is sustainably harvested from the seeds of the Brazilian Rosewood tree no trees are ever cut to produce this oil. Penofin uses the best, most safe raw materials available and does not compromise for the sake of cost. Penofin's formula penetrates deep into the wood's surface, coating the individual fibers of the wood, allowing moisture to pass in and of the wood allowing the wood to breathe. Then, properly dispose of materials at your local hazmat drop-off. IMPORTANT:To avoid spontaneous combustion, submerse all materials soaked in Penofin into a bucket of water and seal it.

For cleanup, use mineral spirits or paint thinner.

Maintain the finish by burnishing it with a soft dry cloth or a floor buffer and touching it up with Penofin as needed.

If desired, after one week apply a polyurethane varnish or lacquer over Penofin.

Buff to a polish with a clean, soft cloth.

Wipe the area dry and repeat the process until grain is filled and desired patina is achieved.

Sand with the grain and keep the area wet with Penofin.

Apply Penofin to a small area with 400 to 600-grit wet/dry sandpaper.

Surface is ready for wet-sanding in 24 hours.

Wait 20-30 minutes, then wipe off excess product.

Stir Penofin thoroughly and then apply one coat using a brush foam pad, or lint-free finishing cloth.Prepare the wood using 150-grit or finer sandpaper.

#Pre painnt wipe rages free

Make sure the wood surface is free of old finishes, paint, wax, grease, polish or dirt and repair any cracks or defects.